"Mounting" Neoprene pads?

luvshinerbock · Post by **luvshinerbock** » Wed Nov 12, 2003 9:34 am

The U-boats from Auralex don't need mounting by their design, however, I've purchased a 1/2" 60 durometer neoprene sheet that I've cut up into strips 2" wide and 6" long to place under my 2x4 floor joists. Do I need to somehow "mount" the pads to the joists, or will careful placement suffice? I'm assuming the weight of the flooring on top of the joists will hold everything in place, but I want to hear your experienced opinions please.

Additionally I've placed GAF Tri-Ply rubber roofing roll on the wooden floor beneath the floating floor...there are some creaks I couldn't repair without going crazy with costs. I intend on placing strips of the GAF on top of the floating floors' joists for additional dampening.

I'm really open to hearing your feedback.

Thanks.

cfuehrer · Post by **cfuehrer** » Wed Nov 12, 2003 10:02 am

For the creaks, get some teflon powder and dust in around to help eliminate some of them.

luvshinerbock · Post by **luvshinerbock** » Wed Nov 12, 2003 10:17 am

Teflon powder? Dusting powder on top of the wooden subfloor will help eliminate the creaks? Really? How does that work?

cfuehrer · Post by **cfuehrer** » Wed Nov 12, 2003 11:01 am

It's an old carpenter thing used to quiet creaky stairs. The teflon powder helps to reduce the friction between boards.

giles117 · Post by **giles117** » Wed Nov 12, 2003 12:29 pm

2x6. Seems kinda big, I'd cut them into 2x3 strips.

I have always used drywall screws to screw them to the stud being careful to sink the screw in halfway so when the neoprene pad compresses the screws dont touch the surface below.

Bryan Giles

I think it's over killl to place the GAF on the studs, but hey every little bit helps. The material is so cheap it can't hurt your pocket too much to experiment.

luvshinerbock · Post by **luvshinerbock** » Wed Nov 12, 2003 1:03 pm

2x6 pieces are too long? Well, if that's the case I just doubled my pad quantity. So, which of you have actually used 2"x3" pads to float a 2x4 floor?
Overkill to put the GAF on the floorjoists? Good enough-just saved myself more $$. My only concern is the creaking floor beneath my floating floor...oh, just thought about something. If I place the pads on the floor where it doesn't creak, maybe I'll be good to go!

Hey, where do I find this teflon powder? Is it costly?

knightfly · Post by **knightfly** » Wed Nov 12, 2003 11:11 pm

" If I place the pads on the floor where it doesn't creak, maybe I'll be good to go! " - Best idea yet -

Also, if you don't want movement above, a dab of construction adhesive on each side of the rubber pads will keep things stable... Steve

giles117 · Post by **giles117** » Wed Nov 12, 2003 11:44 pm

I did. actually I went deeper than that I order a 2" x 1/2" x 15' strip of neoprene.

Cut it into 1.5" Strips. Oc course I used my studs the standard way, not the laying them flat way. If you are laying flat then 2x3 is cool.

Bryan Giles

cfuehrer · Post by **cfuehrer** » Thu Nov 13, 2003 7:03 am

I think one of the carpenters used to use baby powder too if he couldn't get teflon powder. Try any home building supply store.

Michael Jones · Post by **Michael Jones** » Thu Nov 13, 2003 7:13 am

I don't know anything about mounting neoprene, but

I love Shiner Bock too!!!

knightfly · Post by **knightfly** » Thu Nov 13, 2003 6:19 pm

"I love Shiner Bock too" - Hey, you guys wanna go get a room?

(JK) Steve (OK, that was mean, but I gotta give SOMEBODY a ration once in a while...)

Michael Jones · Post by **Michael Jones** » Fri Nov 14, 2003 7:18 am

I already have my ration, AND someone else's!

"Shiner Bock" is a Texas Beer.

knightfly · Post by **knightfly** » Fri Nov 14, 2003 7:54 am

Yeah, I already knew that - but how much mischief can be had without intentional "misunderstandings" ? (In a way, you're lucky - in person, I'm even MORE insufferable on wordplays...) 'course, that's just my FAMILY's version, in reality I'm actually PERFECT...

Steve

luvshinerbock · Post by **luvshinerbock** » Sat Nov 15, 2003 11:09 am

Yup! That good ol Texas-brewed Shiner Bock! Got my first taste in Sept. while in Austin for the ACL Music Festival...brought a case home with me to find, to my delight, that a local distributor is now carrying it!!! [For anyone in the Austin area-gotta say, what a great town/people/vibe! Look forward to next years' festival!]

In the meantime I'm gonna use liquid nails to mount my neoprene pads in place--hope that stuff won't deteriorate the rubber...anyone have any info on this?
Thanks, see y'all soon.

knightfly · Post by **knightfly** » Sun Nov 16, 2003 2:08 am

No problems with liquid nails that I'm aware of - they use it to glue styrofoam insulation to concrete with no problems -

Here's a site that may be able to help, I'm about to crash so didn't look really carefully =

http://www.online-home-improvement-store.com/macco.php

HTH ... Steve